...
首页> 外文期刊>Field Crops Research >Assessment of potato microtuber and in vitro plantlet seed multiplication in field conditions - Growth, development and yield
【24h】

Assessment of potato microtuber and in vitro plantlet seed multiplication in field conditions - Growth, development and yield

机译:田间条件下马铃薯微型块茎和试管苗繁殖的评估-生长,发育和产量

获取原文
获取原文并翻译 | 示例
           

摘要

Microtubers and in vitro plantlets are the basic materials of potato seed production. Minitubers are yield of tubers derived from the first generation of in vitro plantlets or from microtubers. At present the production of minitubers usually takes place under covers - in glasshouse, plastic tunnels and screenhouses. The aim of this research was to assess the possibility of carrying out such multiplications in field conditions. The growth, development and harvesting was estimated in in vitro plantlets, microtubers, minitubers and traditional seed potatoes. Additionally, three terms of in vitro plantlets and microtubers planting in the field were assessed (1st term - second week of April, 2nd term - fourth week of April, 3rd term - last week of June/first week of July). The weather conditions in 2006-2012 impacted greatly on the survival of in vitro plantlets and microtubers planted in a field, especially in the 1st and 3rd terms. In spite of clear differences in the size of planted seed material, the highest reproduction coefficient per one plant was recorded for traditional seed potatoes and microtubers, and the lowest for minitubers. While at the 1st and 2nd terms of planting the average number of tubers from one plant ranged between 6.7 and 8.8, at the 3rd term this value oscillated between 11.2 and 12.4. Analysis of the productivity of particular seed material clearly indicates a much higher share of potentially useful tubers derived from microtubers and in vitro plantlets than of traditional seed potatoes or minitubers. Microtubers and in vitro plantlets planted earlier (1st term of planting) or significantly later (3rd term) produced the greatest minituber yield. Because of a high risk connected with the dying out of plants and maintaining adequate coverage at its earlier planting, the 3rd term of planting of this material was much more favorable. At the same extreme weather conditions (drought and lack of rainfall at the beginning of after planting), which occurred in 2010 contributed to a very strong reduction plants in the field. (C) 2015 Elsevier B.V. All rights reserved.
机译:微型块茎和试管苗是马铃薯种子生产的基本材料。迷你块茎是来源于第一代体外苗或微型块茎的块茎产量。目前,微型薯的生产通常在温室,塑料隧道和筛房的掩护下进行。这项研究的目的是评估在野外条件下进行这种乘法的可能性。在试管苗,微型块茎,微型块茎和传统种薯中估计其生长,发育和收获。此外,还评估了田间种植的三个体外苗和微型块茎的术语(第一学期-4月的第二周,第二学期-4月的第四周,第三学期-6月的最后一周/ 7月的第一周)。 2006-2012年的天气状况对田间种植的试管苗和微块茎的存活产生了重大影响,特别是第一和第三期。尽管种植的种子材料的大小存在明显差异,但传统的种薯和微型块茎的单株繁殖系数最高,而微型块茎的繁殖系数最低。在第一和第二种植期,一株植物的平均块茎数量在6.7至8.8之间,而在第三种植期,该值在11.2和12.4之间波动。对特定种子材料的生产力进行的分析清楚地表明,与传统的种薯或微型块茎相比,源自微型块茎和试管苗的潜在有用块茎的比例要高得多。较早(播种的第一期)或明显较晚(第三期)种植的微型块茎和试管苗产生的微型块茎产量最高。由于与植物死亡和在早期种植时保持足够的覆盖率相关的高风险,该材料的第三个种植期更为有利。在相同的极端天气条件下(种植后开始干旱和降雨不足),2010年发生了这种情况,导致该田减产非常强劲。 (C)2015 Elsevier B.V.保留所有权利。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号