油气水三相流
油气水三相流的相关文献在1997年到2022年内共计141篇,主要集中在力学、石油、天然气工业、机械、仪表工业
等领域,其中期刊论文73篇、会议论文20篇、专利文献781315篇;相关期刊41种,包括中国学术期刊文摘、东北电力大学学报、中国石油大学学报(自然科学版)等;
相关会议15种,包括2012年中国油气计量技术论坛、中国石油学会第十七届测井年会、2011年中国工程热物理学会多相流学术会议等;油气水三相流的相关文献由337位作者贡献,包括周云龙、刘兴斌、郭烈锦等。
油气水三相流—发文量
专利文献>
论文:781315篇
占比:99.99%
总计:781408篇
油气水三相流
-研究学者
- 周云龙
- 刘兴斌
- 郭烈锦
- 孔令富
- 金宁德
- 李英伟
- 胡金海
- 孔维航
- 张西民
- 李军
- 黄春辉
- 孔德明
- 翟路生
- 陈基亮
- 李洪伟
- 何大川
- 刘文红
- 孙斌
- 杨韵桐
- 牟海维
- 蔡辉
- 谢贝贝
- 郝虎
- 于立军
- 刘超
- 叶晶
- 孙迪非
- 张玉辉
- 李雷
- 王延军
- 袁俊文
- 于宏亮
- 于莉娜
- 任英玉
- 伍国柱
- 关月波
- 刘刚
- 吴伟超
- 周芳德
- 宋景东
- 崔耀耀
- 张玮
- 李广军
- 李庆银
- 洪文鹏
- 牛俊邦
- 王玉庆
- 王瑜
- 王静
- 田小强
-
-
王潜龙;
荆波;
龚俊;
李丙贤;
翁羽
-
-
摘要:
胜利海上油田累计开发时间长达26 a,部分平台采油井进入开采后期,出砂严重,油田管线寿命缩短,可能发生原油泄漏事故。针对平台连接输送管中的含砂冲蚀现象进行了分析探讨。使用CFD数值分析方法,考虑油气水三相流体与砂粒之间的相互作用,获得了该管道在不同输送量和含沙量下的砂粒流动特性及其对管壁的腐蚀特性。结果表明:砂粒堆积主要发生在管道弯头的外侧区域。冲蚀率随着输液量的增加而增大,冲蚀范围也同时增加。相同输液量条件下,冲蚀率随着含砂率的增加而增大,但对冲蚀范围无明显影响。
-
-
胡金海;
黄春辉;
刘晓磊;
杜佳楠;
宋纯高;
李屹威
-
-
摘要:
早期的油气水三相流测井解释方法需要有密度参数,但放射性密度计早已停用,而压差密度计在流量100 m3/d以下的套管内,测量密度的分辨率极低无法应用.提出了一种基于光纤探针、阻抗传感器和涡轮流量计的组合测井仪,对该仪器在油气水三相流模拟实验装置上进行实验,分别建立光纤探针、涡轮流量计及阻抗传感器在三相流下的响应规律图版,通过图版插值的方法建立油气水三相流解释方法.实验结果表明,不同气量下涡轮响应与光纤探针响应关系曲线、涡轮响应与油水两相流量关系曲线、油水两相含水率与油水两相流量关系曲线,可用于解释气相流量、油水两相流量及油水两相含水率.
-
-
-
-
钟强;
骆正山
-
-
摘要:
Marine riser is an important part of offshore oil and gas gathering and transportation system, which is used to connect submarine oil and gas wellheads and offshore oil and gas gathering and transportation stations.In oil and gas storage and transportation projects, marine oil and gas gathering and transportation media are mostly oil-gas-water three-phase fluids.In order to investigate the coupled vibration problem of the oil-gas-water three-phase flow marine riser system under severe slug flow, numerical calculation and empirical research were carried out.Based on the multiphase fluid mechanics theory and kinetic theory, a three-phase severe slug flow model of oil-gas-water and structural dynamics model were constructed.Combining these two models, the coupled vibration response process of the riser was simulated, and the L-type oil-gas-water threephase flow riser system with the inclined pipe tilt angle of 3°was designed and tested.Comparing the calculated and tested values, the results showed that the proposed coupled vibration response model was more suitable for studying the coupled vibration response of marine riser caused by the oil-gas-water three-phase of flug flow than the severe slug flow transient mathematical model, and the simulation of results were in good agreement with the experimental results.The pressure and displacement of the riser bottom changed periodically, and the period of change was basically the same;the pressure of fluid was the key factor that caused the coupled vibration response of the riser system.These research results provide a reference for the analysis of the coupled vibration response characteristics and structural design of the oil-gas-water three-phase flow marine riser system under severe slug flow.%海洋立管是海上油气集输系统的重要组成部分,用于连接海底油气井口与海上油气集输站.在油气储运工程中,海洋油气集输介质多为油气水三相流体.为了研究油气水三相流海洋立管系统在严重段塞流作用下产生的耦合振动问题,进行了数值计算与实证研究.基于多相流体力学与动力学理论,构建了油气水三相严重段塞流模型和海洋立管结构动力学模型,结合这2个模型,模拟了立管耦合振动响应过程,并设计了下倾管倾斜角度为3°的L型油气水三相流立管系统进行实验.对模型计算值和实测值进行对比,结果表明:所提出的耦合振动响应模型比现有严重段塞流瞬态数学模型更适用于油气水三相段塞流引起的海洋立管耦合振动响应问题的研究,计算结果与实验结果较吻合;立管底部压强与底部位移呈周期性变化,且变化周期基本一致;流体压强是引发立管系统耦合振动响应问题的关键因素.研究结果为油气水三相流海洋立管系统在严重段塞流作用下的耦合振动响应特性分析及其结构设计提供了参考.
-
-
杨韵桐12
-
-
摘要:
油田开发中油气水三相流共存是普遍存在的现象,由于气相的干扰,使原有测量两相流的仪器不能满足多相流测量精度的要求。为了解决油井井下油气水三相流流量测量精度低的问题,设计了低产液高含水条件下,井下气液分离装置的物理模型。在此基础上,构建了气液分离装置模型。利用Fluent模拟仿真软件对模型进行数值模拟,得到20~60m^3/d流量下气液分离的效率,仿真结果显示该模型气液分离效率高,具有很高的可行性。设计的气液分离装置为整体实验样机设计制作奠定了理论基础。
-
-
杨韵桐
-
-
摘要:
油田开发中油气水三相流共存是普遍存在的现象,由于气相的干扰,使原有测量两相流的仪器不能满足多相流测量精度的要求.为了解决油井井下油气水三相流流量测量精度低的问题,设计了低产液高含水条件下,井下气液分离装置的物理模型.在此基础上,构建了气液分离装置模型.利用Fluent模拟仿真软件对模型进行数值模拟,得到20~60 m3/d流量下气液分离的效率,仿真结果显示该模型气液分离效率高,具有很高的可行性.设计的气液分离装置为整体实验样机设计制作奠定了理论基础.
-
-
胡实;
韩连福;
赵鸣;
张自成;
王延军;
刘兴斌
-
-
摘要:
Serial communication is often used in conventional data acquisition system.However,laptop without serial port is often used in the industrial measurement.So,data acquisition using USB communication is more suitable for commercial measure.To facilitate the measurement of oil-gas-water three phase flow parameters,a flow parameter acquisition system is designed.The system include upper monitor and data acquisition module.The upper monitor controls the data acquisition module to collect the three-phase flow parameters through the USB port.Transfer pressure,temperature,optical fiber and other parameters are collected by data acquisition card to upper monitor with USB.Use the LabVIEW software program to control data in the upper monitor.Data acquisition,processing and analysis is realized.The experiments show and data analysis that the acquisition system has the characteristics of high precision,high stability.%传统数据采集系统常采用串口采集数据,但工业测量中常使用没有串口的笔记本电脑,故基于USB的数据采集更适用于工业测量.为实现油气水三相流流动参数测量,搭建流动参数采集系统,系统包含上位机与数据采集模块.上位机通过USB控制数据采集模块采集三相流流动参数,将采集的压强、温度和光纤折射率等参数通过USB传输至上位机,在上位机LabVIEW软件中编程对数据进行控制,实现数据实时采集、处理与分析.实验表明和数据分析该采集系统具有精度高、稳定性高等特性.
-
-
骆正山;
钟强
-
-
摘要:
氮气式水击泄压阀的压力精度设定问题与油气管道系统能否安全运行紧密相关,为进一步提高泄压阀的设定压力精度,构建了油气水三相流耦合水击模型和阀芯运动力学模型;根据泄压阀的工作原理,对泄压阀阀芯的受力情况进行分析,建立水击压强、氮气压力、弹簧力之间的数学联系;实现了油气水三相流耦合水击模型和运动力学模型的融合.研究结果表明:构建的数学模型能准确地计算出符合实际工况的水击压强、氮气压力、弹簧力的理论数值;水击压强、氮气压力与弹簧力大小呈周期性变化;氮气压力与弹簧力设定数值的确定,可进一步提高泄压阀的设定压力精度.
-
-
赵鹏;
刘衍钊;
于瑞钢
-
-
摘要:
在进行油气水三相流混输管路压降的计算中,需要涉及到很多内容,不仅包括数值计算知识,同时还包括流体力学以及数学建模等内容.鉴于多相流动计算机理的复杂性,并没有规范系统的计算方法进行研究,主要针对油气水三相流混输管路压降计算方法进行探析,希望为油气水三相流混输管路压降的计算研究提供一定帮助.%In the calculation of the pressure drop of the mixed pipelines of oil-gas-water three-phase flow,it involves a lot of content,including not only the numerical calculation knowledge,but also the contents of fluid mechanics and mathematical modeling, in view of the multi-phase flow computer.The complexity of the theory is not regulated by systematic calculation methods.In the following,this paper analyzes the pressure drop calculation method for the mixed pipelines of oil and gas and water three-phase flow, hoping that it is a pressure drop for the mixed pipelines of oil and gas and water three-phase flow.Computational studies provide some help.
-
-
王颖;
汪泓;
杨文军
- 《2012年中国油气计量技术论坛》
| 2012年
-
摘要:
本文介绍了油气水三相流检定试验装置设计,主要包括装置的技术指标、工艺流程、功能及结构.油气水多相流量标定试验装置按功能分为稳压供水、稳压供油及稳压供气单元;油、水和气流量测量调节单元;液体流量自检单元;水表、油表及气表检定单元;模拟井筒单元;控制单元及视频监控单元。该装置既可以进行单相和多相流量、含水等计量仪器的检定校验,又可以模拟油气水三相流的流型流态以及进行井下测试仪器的开发,开展油气水三相流一些前沿性和基础性的实验,是一套功能比较完备的实验装置,整体技术指标达到国内领先水平.
-
-
-
-
-
-
-
-
-