首页> 外文期刊>Thermal engineering >Study of Connected System of Automatic Control of Load and Operation Efficiency of a Steam Boiler with Extremal Controller on a Simulation Model
【24h】

Study of Connected System of Automatic Control of Load and Operation Efficiency of a Steam Boiler with Extremal Controller on a Simulation Model

机译:带有极限控制器的蒸汽锅炉负荷和运行效率自动控制互联系统的仿真模型研究。

获取原文
获取原文并翻译 | 示例
           

摘要

The problems of operation effectiveness increase of steam boilers are considered. To maintain the optimum fuel combustion modes, it is proposed to use an extremal controller (EC) determining the value of airflow rate, at which the boiler generating the desired amount of heat will consume a minimum amount of fuel. EC sets the determined value of airflow rate to airflow rate controller (ARC). The test results of numerical simulation dynamic nonlinear model of steam boiler with the connected system of automatic control of load and combustion efficiency using EC are presented. The model is created in the Simulink modeling package of MATLAB software and can be used to optimize the combustion modes. Based on the modeling results, the conclusion was drawn about the possibility in principle of simultaneously boiler load control and optimizing by EC the combustion modes when changing the fuel combustion heat and the boiler characteristics and its operating mode. It is shown that it is possible to automatically control the operation efficiency of steam boilers when using EC without applying the standard flue gas analyzers. The article considers the numerical simulation dynamic model of steam boiler with the schemes of control of fuel consumption and airflow rate, the steam pressure and EC; the purpose of using EC in the scheme with linear controllers and the requirements to the quality of its operation; the results of operation of boiler control schemes without EC with estimation of influence of roughness of thermal mode maps on the nature of static and dynamic connection of the control units of fuel consumption and airflow rate; the phase trajectories and the diagrams of transient processes occurring in the control scheme with EC with stepped changing the fuel quality and boiler characteristics; analysis of modeling results and prospects for using EC in the control schemes of boilers.
机译:考虑了蒸汽锅炉运行效率提高的问题。为了维持最佳的燃料燃烧模式,建议使用确定空气流速值的极值控制器(EC),在该值下,产生所需热量的锅炉将消耗最少的燃料。 EC将确定的风量值设置给风量控制器(ARC)。给出了采用EC自动控制负荷和燃烧效率的连接系统的蒸汽锅炉数值模拟动态非线性模型的测试结果。该模型是在MATLAB软件的Simulink建模包中创建的,可用于优化燃烧模式。根据建模结果,得出了在改变燃料燃烧热和锅炉特性及其运行模式时,同时进行锅炉负荷控制和通过EC优化燃烧模式的可能性的结论。结果表明,在不使用标准烟气分析仪的情况下,使用EC可以自动控制蒸汽锅炉的运行效率。通过控制油耗和风量,蒸汽压力和EC的方案,考虑了蒸汽锅炉的数值模拟动力学模型。在带有线性控制器的方案中使用EC的目的及其对操作质量的要求;不带EC的锅炉控制方案的运行结果,并估计了热模式图的粗糙度对燃料消耗和气流速率控制单元的静态和动态连接性质的影响; EC的控制方案中逐步改变燃料质量和锅炉特性的相轨迹和过渡过程图;分析建模结果和在锅炉控制方案中使用EC的前景。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号