首页> 美国卫生研究院文献>Micromachines >Experimental Investigation of Air Compliance Effect on Measurement of Mechanical Properties of Blood Sample Flowing in Microfluidic Channels
【2h】

Experimental Investigation of Air Compliance Effect on Measurement of Mechanical Properties of Blood Sample Flowing in Microfluidic Channels

机译:空气顺应性对微流道血样力学性能测量的实验研究

代理获取
本网站仅为用户提供外文OA文献查询和代理获取服务,本网站没有原文。下单后我们将采用程序或人工为您竭诚获取高质量的原文,但由于OA文献来源多样且变更频繁,仍可能出现获取不到、文献不完整或与标题不符等情况,如果获取不到我们将提供退款服务。请知悉。

摘要

Air compliance has been used effectively to stabilize fluidic instability resulting from a syringe pump. It has also been employed to measure blood viscosity under constant shearing flows. However, due to a longer time delay, it is difficult to quantify the aggregation of red blood cells (RBCs) or blood viscoelasticity. To quantify the mechanical properties of blood samples (blood viscosity, RBC aggregation, and viscoelasticity) effectively, it is necessary to quantify contributions of air compliance to dynamic blood flows in microfluidic channels. In this study, the effect of air compliance on measurement of blood mechanical properties was experimentally quantified with respect to the air cavity in two driving syringes. Under periodic on–off blood flows, three mechanical properties of blood samples were sequentially obtained by quantifying microscopic image intensity ( ) and interface ( ) in a co-flowing channel. Based on a differential equation derived with a fluid circuit model, the time constant was obtained by analyzing the temporal variations of = 1/(1– ). According to experimental results, the time constant significantly decreased by securing the air cavity in a reference fluid syringe (~0.1 mL). However, the time constant increased substantially by securing the air cavity in a blood sample syringe (~0.1 mL). Given that the air cavity in the blood sample syringe significantly contributed to delaying transient behaviors of blood flows, it hindered the quantification of RBC aggregation and blood viscoelasticity. In addition, it was impossible to obtain the viscosity and time constant when the blood flow rate was not available. Thus, to measure the three aforementioned mechanical properties of blood samples effectively, the air cavity in the blood sample syringe must be minimized ( = 0). Concerning the air cavity in the reference fluid syringe, it must be sufficiently secured about = 0.1 mL for regulating fluidic instability because it does not affect dynamic blood flows.
机译:空气顺应性已被有效地用来稳定由注射泵引起的流体不稳定性。它也已用于在恒定剪切流量下测量血液粘度。然而,由于更长的时间延迟,难以量化红细胞(RBC)的聚集或血液粘弹性。为了有效地量化血液样本的机械性能(血液粘度,RBC聚集和粘弹性),有必要量化空气顺应性对微流体通道中动态血流的贡献。在这项研究中,相对于两个驱动注射器中的气腔,通过实验量化了空气顺应性对血液力学性能测量的影响。在周期性的开-关血流下,通过对同流通道中的显微图像强度()和界面()进行量化,依次获得了三个血液样本的机械性能。基于从流体回路模型导出的微分方程,通过分析时间变化= 1 /(1-)获得时间常数。根据实验结果,通过将空气腔固定在参考液体注射器(〜0.1 mL)中,时间常数显着降低。但是,通过将空气腔固定在血液样本注射器中(〜0.1 mL),时间常数显着增加。鉴于血液样本注射器中的气孔极大地延迟了血流的瞬时行为,因此阻碍了RBC聚集和血液粘弹性的量化。另外,当无法获得血液流速时,不可能获得粘度和时间常数。因此,为了有效地测量血液样本的上述三个机械性能,必须最小化血液样本注射器中的气腔(= 0)。关于参考流体注射器中的气腔,必须充分固定约= 0.1 mL,以调节流体的不稳定性,因为它不会影响动态血流。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
代理获取

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号