首页> 美国卫生研究院文献>other >Determination of airborne wood dust in Button samples by diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS)
【2h】

Determination of airborne wood dust in Button samples by diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS)

机译:漫反射率红外傅里叶变换光谱法测定按钮样品中的空气灰尘测定(漂移)

代理获取
本网站仅为用户提供外文OA文献查询和代理获取服务,本网站没有原文。下单后我们将采用程序或人工为您竭诚获取高质量的原文,但由于OA文献来源多样且变更频繁,仍可能出现获取不到、文献不完整或与标题不符等情况,如果获取不到我们将提供退款服务。请知悉。

摘要

Emerging concerns regarding the toxicity of inhaled wood dust support the need for techniques to quantitate wood content of mixed industrial dusts. The diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) analysis technique was applied to the determination of wood content of 181 inhalable dust samples (geometric mean concentration: 0.895 mg/m3; geometric standard deviation: 2.73) collected from six wood product industry factories using 25mm glass fibre filters with the Button aerosol sampler. Prior to direct DRIFTS analysis the filter samples were treated with ethyl acetate and re-deposited uniformly. Standards ranging from 125 μg to 4000 μg were prepared for red oak, southern yellow pine, and red cedar and used for quantitation of samples depending upon the wood materials present at a given factory. The oak standards spectra were quantitated by linear regression of response in Kubelka-Munk units at 1736 cm−1, whereas the pine standards and the cedar standards spectra were quantitated by polynomial regression of response in log 1/R units at 1734 cm−1, with the selected wavenumbers corresponding to stretching vibration of free C=O from cellulose and hemicelluloses. For one factory which used both soft- and hardwoods, a separate polynomial standard curve was created by proportionally combining the oak and pine standards polynomial regression equations based on response (log 1/R) at 1734 cm−1. The analytical limits of detection were approximately 52 μg of oak, 20 μg of pine, 30 μg of cedar, and 16 μg of mixed oak and pine for the factory with mixed woods. Overall, the average of dry wood dust percentage of inhalable dust was approximately 56% and the average dry wood dust weight was 0.572mg for the Button samples. Across factories, there were statistically significant differences (p<0.001) for the percentage of dry wood dust in inhalable dust with factory averages ranging from 33.5 to 97.6%.
机译:关于吸入木粉尘的毒性的新担忧支持对定量混合工业粉尘中木材含量的技术的需求。采用漫反射红外傅里叶变换光谱法(DRIFTS)分析测定了181个可吸入粉尘样品的木材含量(几何平均浓度:0.895 mg / m 3 ;几何标准偏差:2.73)来自六个木制品工业工厂的工厂,它们使用25mm玻璃纤维过滤器和Button气溶胶采样器。在直接DRIFTS分析之前,将过滤器样品用乙酸乙酯处理,然后均匀地重新沉积。针对红橡树,南方黄松和红雪松制备了125μg至4000μg的标准液,并根据给定工厂中使用的木材材料将其用于样品定量。通过对1736 cm -1 处的Kubelka-Munk单位的响应进行线性回归来定量测定橡树标准光谱,而通过对数1 / R中的响应进行多项式回归来定量测定松树标准和雪松标准光谱。单位为1734 cm -1 ,选定的波数对应于纤维素和半纤维素中游离C = O的拉伸振动。对于同时使用软木和硬木的一家工厂,通过在1734 cm -1 下基于响应(log 1 / R)按比例组合橡木和松木标准多项式回归方程,创建了单独的多项式标准曲线。对于混合木材工厂,检测的检出限为约52μg橡木,20μg松木,30μg雪松和16μg混合橡木与松木。总体而言,Button样品的可吸入粉尘的平均干木粉尘百分比约为56%,平均干木粉尘重量为0.572mg。在整个工厂中,干粉尘在可吸入粉尘中的百分比在统计学上有显着差异(p <0.001),工厂平均水平在33.5%至97.6%之间。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
代理获取

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号