Effects of drug-carrier interactions on drug dissolution from binary and ternary matrices.

摘要

For nearly five decades, pharmaceutical researchers have studied solid solutions of drugs in polymers as a potential means to enhance the dissolution of drugs with poor aqueous solubility. This has become of greater importance in recent years because most new potential drug compounds (new chemical entities) exhibit poor water solubility and present great challenges to scientists who must design dosage forms from which the drugs are bioavailable.;During the formulation of a solid solution, the drug undergoes physical but not chemical alterations that increase its chemical potential in the formulation relative to that of the pure drug in its stable form. This increased chemical potential is responsible for enhanced dissolution as well as physical instabilities, such as amorphous to crystalline conversions and precipitation within the solid state. The chemical potential is derived from the Gibbs free energy, so it is reasonable to explain the behavior of solid solution systems in terms of thermodynamics. Solid solutions and dispersions have been extensively studied by pharmaceutical scientists, both with regard to manufacturing aspects and the proposal of various models in attempts to explain the physical bases for how these systems work.;Recently, Dave and Bellantone proposed a model based on the thermodynamic changes resulting from the formulation of binary solid solutions of a drug in the polymer PVP. Their model introduced a modification of the F-H theory, which was used to quantify the drug-polymer interaction energies and calculate the entropy of mixing of the drug and polymer.;In this work, the model of Dave and Bellantone was extended to include three-component systems, consisting of one drug mixed in a carrier matrix consisting of mixture of two polymers or a polymer and a surfactant. For this research, solid solutions were formed using various drug weight fractions in the formulations. The study focused on the following points: (1) Prepare solid solution formulations and perform appropriate physical characterizations. (2) Characterize the increase in drug dissolution rates resulting from solid solution formulations. (3) Relate the initial dissolution rates to the drug solubility. (4) Explain the solubility enhancement from solid solution dosage in terms of the drug polymer interactions using the extended thermodynamic model.;Two poorly water soluble drugs, levonorgestrel (LEVO) and ethinyl estradiol (EE) were formulated in seven solid solution preparations comprised of four carrier systems. Materials used as carriers included various combinations of the polymers PVP K-30, Copovidone (COP), Poloxamer 182, and the surfactant TweenRTM 20. Additionally, ibuprofen (IBU) was used in three formulations consisting of various combinations of PVP K-30, Copovidone and TweenRTM 20. Formulations with various drug weight fractions (0.5%--30%) were prepared using the solvent evaporation technique. Each formulation was tested for dissolution using intrinsic dissolution apparatus (USP). The solid solutions were compressed into tablets into the sample die that maintained a constant surface area during the dissolution process.;DSC, XRD and NIRS scans identified that the crystalline peaks of the drug disappeared with the addition of the polymer for all ratios of EE, indicating the formation of solid solutions (to within the limits of detection of the equipment). This was also observed for the LEVO dispersions up to 10% drug loading. At higher drug loading, solutions were formed but some small degree crystallinity was also present.;For each experiment, the initial dissolution rates were obtained from the slope of the mass dissolved vs. time plots taken at early times, and volume normalized initial dissolution rates RV were calculated by dividing the initial dissolution rate by the volume fraction of the drug in the formulation. Comparison of the RV values for the various formulations with a reference RV (typically that of the pure drug or of the formulation with the highest polymer content) allowed calculation of relative volume normalized dissolution rates (RNV). The various RNV were used in the thermodynamic model for data analyses and to determine the interactions between the drug and carrier molecules. It was generally seen that RNV increased with decreased drug fraction, and was adequately modeled by the equations derived from the extended thermodynamic model.;It was concluded that the model proposed for the binary and ternary systems successfully represented the mechanism of drug-polymer interaction and the energy changes taken place within the dispersion systems. The dissolution data analysis and subsequent understanding of physical modifications in the dispersion systems characterized by XRD, NIRS and DSC further substantiated the findings. The understanding of the fundamental physical might help scientists to predict the effects of mixing various drugs and polymers, and the effects of varying ratios.