【24h】

EVALUATION OF GLASS FIBER HEPA FILTERS AS A FUNCTION OF MEDIA VELOCITY

机译:玻璃纤维高效过滤器作为介质速度的评估

获取原文
获取原文并翻译 | 示例

摘要

Section FC of the ASME AG-1 Code addresses glass fiber HEPA filters and restricts the media velocity to a maximum of 2.54 cm/s (5 ft/min). Advances in filter media technology allow glass fiber HEPA filters to function at significantly higher velocities and still achieve HEPA performance. However, diffusional capture of particles < 100 nm is reduced at higher media velocities due to shorter residence times within the media matrix. Therefore, it is unlikely that higher media velocities for HEPA filters will be allowed without data to demonstrate the effect of media velocity on removal of particles in the smaller size classes. In order to address this issue, static testing has been conducted to generate performance related data and a range of dynamic testing has provided data regarding filter lifetimes, loading characteristics, changes in filter efficiency and the most penetrating particle size over time. Testing was conducted using 31 cm × 31 cm × 29 cm deep pleat HEPA filters supplied from two manufacturers. Testing was conducted at media velocities ranging from 2-4.5 cm/s. using a solid aerosol challenge composed of potassium chloride. Two set of media velocity data were obtained for each filter type. In one set of evaluations, the maximum aerosol challenge particle size was limited to 3 μm, while particles above 3 μm were not constrained in the second set. This provided for considerable variability in the challenge mass mean diameter and overall mass loading rate. Results of this testing will be provided to the ASME AG-1 FC Committee for consideration in future versions of the HEPA standard. In general, the initial filter efficiency decreased with increasing media velocity. However, initial filter efficiencies were generally good in all cases. Filter efficiency values averaged over the first ten minute of the loading cycle ranged from 99.970 to 99.996 %. Additionally, the most penetrating particle size was observed to decrease with increasing media velocity, with initial values ranging from 194 to 134 nm.
机译:ASME AG-1规范的FC节涉及玻璃纤维HEPA过滤器,并将介质速度限制为最大2.54 cm / s(5 ft / min)。过滤介质技术的进步使玻璃纤维HEPA过滤器能够以更高的速度运行,并且仍能达到HEPA性能。但是,由于介质基质中的停留时间较短,因此在较高的介质速度下,小于100 nm的颗粒的扩散捕获得以减少。因此,如果没有数据来证明介质速度对较小尺寸级别的颗粒去除的影响,则不太可能允许HEPA过滤器具有更高的介质速度。为了解决这个问题,已经进行了静态测试以生成与性能相关的数据,并且一系列动态测试提供了有关过滤器寿命,负载特性,过滤器效率的变化以及随时间变化最大的粒度的数据。使用两家制造商提供的31厘米×31厘米×29厘米深的褶皱HEPA过滤器进行测试。测试以2-4.5 cm / s的介质速度进行。使用由氯化钾组成的固体气溶胶激发剂对于每种过滤器类型,获得了两组介质速度数据。在一组评估中,最大气溶胶激发颗粒尺寸限制为3μm,而在第二组中不限制3μm以上的颗粒。这提供了挑战质量平均直径和总质量加载率的显着差异。测试的结果将提供给ASME AG-1 FC委员会,供以后版本的HEPA标准考虑。通常,初始过滤器效率随着介质速度的增加而降低。但是,在所有情况下,初始过滤器效率通常都很好。在加载周期的前十分钟内,平均过滤器效率值介于99.970%至99.996%之间。另外,观察到最穿透的粒度随着介质速度的增加而减小,其初始值范围为194至134 nm。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号